PSA Marelli IAW 6LP Is Safe Read and Write with Foxflash on OBD? Foxflash doesn’t read it for obd. It will do it in boot mode. If need to read it by OBD, go for ktag. If have foxflash tool, do it like this. PSA Marelli 6LP HW01 MARELLI 6LPx Vers.1 [ ST10F280… Read More »
Question: I can’t do MED17.5 TC1766 1.5 mb file with foxflash by obd? any solution? Solution: Use bench or boot mode. Bench mode: BOSCH MED17.5 [ 1766 ] – VW, Audi, Seat, Skoda [Gasoline] To read and write use the following driver: → BENCH TRICORE → VW / AUDI / SEAT / SKODA… Read More »
Foxflash tool failed to read and write Dacia Duster SID306 ECU via OBD? voltage is 13V+. If fail to read SID306 by OBD, try boot mode. Foxflash SID306 boot pinout SIEMENS CONTINENTAL SID305/SID306 V.1 [ TC1766 INT.F.] – Renault, Nissan Read and Write ECU Connect with the multifunction cable the following pinout and… Read More »
How to read and write psa edc15c2 ECU with Foxflash? Remove eeprom or boot mode. By boot its simple. Pin 24 on the ground with resistor of 5k Power off Pin 24 on the ground Power on No Pin 24 on the ground. BOSCH EDC15 C2 [ C167 ] – Peugeot, Citroen [Diesel]… Read More »
User feedback: Foxflash read and write PSA DCM7.1a in boot mode successfully. Read ok Write ok Checksum ok. the foxflash tool does it automatically. Read also: http://www.pcmtuner.org/foxflash-read-and-write-citroen-jumper-dcm7-1b/
Problem: I have a problem with Foxflash. It failed to read Bosch EDC16C31 volvo xc90 2007 model via OBD. Solution: Denso Volvo 2016 must unlock bench and write obd. No k-line at OBD in volvo. Bench it. Foxflash pinout to Volvo EDC16C31 BOSCH EDC16 C31 [ MPC561/2 ] – Volvo [Diesel] To read and write… Read More »
Foxflash new test feedback: A Little late night Chevrolet Delco E78 ECU cloning and vin swapping. Read and write successfully using foxflash. Chevrolet Delco ECUs 1.2-1.4 16V Delco E78 Full System *CAN Here is the GM Delco E78 ECU bench pinout Read and write ok
Iveco edc7uc31 truck ecu read and write successfully with foxflash. BOSCH EDC7 UC31 [ MPC561/2 ] [Diesel] pinout to foxflash Connect the multifunction cable as follows, use the Bench Box and the D48CONN04 adapters: To read and write use the following driver: → BENCH MODE → [brand] → MPC561 – [brand] → EDC7 UC31 … Read More »
Question: How to read and write Volkswagen EDC15P+ with foxflash? I can’t find a driver for it. Answer: Seat Arosa Bosch EDC15P+ OBD BENCH BOOT Ford Galaxy Bosch EDC15P+ OBD BENCH BOOT any of them can do, better use bench read and write for safe, you also can do bench full backup, then… Read More »
Problem: I have problem with opel delco e98. I write eeprom with foxflash. and after that ecu no communication. Id make but can’t write backup. reading error wrong file dimension. Solution: Wrong file selected. You read flash but write backup. Select flash and write flash. If still gives error when write flash, check wiring diagram… Read More »