Question: Xhorse multi prog failed to read the Renault Continental ECU SID309. The error is: pflash unprotection failed – connection failed. This ECU is currently not supported by multiprog. sid307, sid309 and sid310 have Tprot password active; if you don’t find before password through obd then you can’t have access to boot. What tools… Read More »
Problem: Mercedes VITO, edc16c2 ECU. Foxflash read ok via OBD, OBD Write ok but car doesn’t start. Solution: It was tested to work couple times so far, but maybe checksum wasn’t done with foxflash on this case. Checksum is fucked up. If read with foxflash, power supply is important. Radiator turning on while… Read More »
FormulaFlash ECU and TCU programmer released a big update on Jan. 7th, 2024. We’re excited to introduce the latest FormulaFlash update, packed with cutting-edge features for ECU programming and optimization: What’s New? • Expanded ECU Support: • MG1CA007, MG1CA811, MG1CA920, MG1CP002, MG1CP007, MG1CS001, MG1CS002SPC5777, MG1CS002TC298, MG1CS003 (DME 861), MG1CS008, MG1CS011, MG1CS015, MG1CS016, MG1CS017, MG1CS018,… Read More »
Problem: No possible to read and write edc16c3 PSA ECU with foxflash on bench. Any solution? Solution: Bad connection. Check the bench pinout in foxflash. You must add a ground wire for bench box because now you connect only the resistor. If still not working just remove resistor and connect directly the brown wire to… Read More »
CG FC200 will do VAG MED17.5 ECU IMMO OFF in device directly without 3rd party software. Check instructions below: Run FC200 software, select Bosch MED17.5 TC1766 ECU. View wiring diagram Connect MED17.5 ECU with FC200 following the diagram Identify ECU. Read and save Dflash. Then read and save Pflash. Go to ECU selection, select… Read More »
OBDSTAR DC706 as well as X300 Classic G3 with ECU flasher license released a big update on ECM software V31.50. Adds many new ECUs and IMMO OFF function directly in the device including GM AcDelco E83, Bosch ME7.8, ME7.8.8, M7.9.7, M7.9.7.1, MEV17.4 ECUs etc. ECM V31.50 1. Details Added: • Add ALFA ROMEO MAGNETI… Read More »
Foxflash new user report: It’s not on the list so we’re adding info. ECU: EDC17C70 Brand: FORD Model: FOCUS MK3 FL 2017 Engine: 1.5 TDCi 120km Operation mode: OBD vr Read via OBD ok Write via OBD ok Read +- 15min / write maybe 3min but it stayed at 0% for a long time after… Read More »
Today we will compare Xhorse multi prog with CG100 Prog III related to airbags. Let’s compare the difference between these two programmers. Connect both of them to PC. CG100 can also automatically repair airbags when you are connected to it. It can repair 90% of airbags. Hhe will write a clear dump. Multi prog… Read More »
Question: I need help to clear crash from this unit from a Toyota Highlander. 89170-0E400 Denso RH850 R7F701A223 I need pinout for read cpu. What software supports this module? CG100/CG100X will read this airbag module. iProg pro original also reset airbag crash for this module. OBDSTAR P50/X300 Classic G3 will also reset crash for this… Read More »
How-to: clone GM Buick 6T30 transmission gearbox TCU with Launch X431 ECU & TCU programmer on bench. Quick search 6T30 and select Buick Encore 2013-2019 6T30 gearbox TCU. Choose bench mode. Check wiring diagram. Connect 6T30 Gearbox TCU with Launch x431 ecu & tcu programmer Connect TCU. Back up FLASH data of the original TCU.… Read More »
