Problem: How to solve this problem. after installing new Foxflash version 1.4.2 on windows 7? Error “Unable to Check Server”. I always use Windows 7, this happened after the update. Solution: This message will appear on Win7 system. On Win10 it does not appear. Some use it on Windows 7, getting this message for a… Read More »
Foxflash read and write Iveco STRALIS EDC17CV41 ECU on bench successfully. To read and write use the following driver: → BENCH MODE → Iveco → TC1797 – Iveco → EDC17 CV41 Read ok, write ok Checksum by foxflash. EGR + DPF off. Check pinout here http://www.pcmtuner.org/edc17cv41-pinouts-to-pcmtuner-and-foxflash/
Audi A6 2.0l tdi 2010 Possible to read and write with foxflash via obd? Tried to read via OBD but failed. It is written, bench or boot mode. 2010 has Tprot. Only bench mode to bypassing tprot. Bench write and read ok. Check bench pinout here http://www.pcmtuner.org/foxflash-read-and-write-audi-a4-2-0-edc17cp14-ecu/
Foxflash read and write Mazda CX-5 Denso ECU SH1K via OBD successfully. OBD Read/Write worked fine. Photos added. Read time takes 30 minutes. But it works. Select ->OBD driver ->Mazda ->Mazda CX-5 ->2.2 SKYACTIV-D Denso SH1X *CAN Voltage 14V. EGR Off.
Question: I need to read the data from 2013 Ford Focus dashboard mcu d70f3425 , will VVDI prog read it? if not what ? Does anyone have a pinout? Yes, both CG100X and VVDI prog will read this dashboard. This is the pinout for d70f3425 , read by cg100x. And here is the… Read More »
It is a Ford Transit Visteon with DCU101 ECU. Foxflash will read and write this ECU via OBD. It is DCU 101 but protocol DCU 102/108 works. Select OBD drive ->Ford ->Transit ->2.2/2.4 TDCI E4 FOMOCO VISTEON DCU 102/108 *CAN Read ok via OBD. Write OK via OBD. Checksum by foxflash. EGR + DPF OFF.… Read More »
FormulaFlash released new software 1.0.0.7 on October 21st, 2024. 1. Adds ME788 BSL mode, read, write, clone, checksum and IMMO Off, idle speed adjustment, power upgrade (World’s first) 2. New checksum: Simos 8.x, MSD80, MSD81, MSD85, MSD87 Upcoming updates: 1. ME7.8, ME797, ME7971 virtual reading and writing, checksum, one-click operation mode for immo off, idle… Read More »
Problem: Successfully read and write Audi Bosch Md1cs004 ECU with Foxflash. SCR off. But scanner shows fault code U2A200 after scr off. Reductant quality sensor no communication. How to fix it? Solution: Just disconnect adblue pump. Disconnect adblue if the fault doesn’t disappear do dtc off solution as well. User… Read More »
It is a Yamaha MT 07 2021 with R5F10DMFJ chip. How to read/write this massive chip? What tool can be used? Here is the clue. UPA 1.3 cannot read, you need pogrammer for this mcu smok, xtool, carprotool, CG100/CG100X,vvdi prog ect Here is the pinout wiring connection. Feedback: I finally bought a CG100x from iecutool.ru.… Read More »
Landrover Freelander2 CEM successfully cloned by OBDSTAR DC706 programmer. Delphi CEM M30882F+ 95320 DC706 clone this CEM on bench mode using P004 adapter. Read EXT eeprom 95320 Read EXI eeprom decrypted Read INT flash M30882F Read configuration zone Write EXT eeprom 95320 Write EXI eeprom decrypted Write INT flash M30882F Write configuration zone Car starts… Read More »
