Fetrotech Black Read and Write MED9.1 MPC562
Foxflash Delphi DCM3.7AP Jtag Pinout
How to read/write a Delphi DCM3.7AP ecu with foxflash ecu programmer? Foxflash will read Cheverolet, GM and Opel Delphi DCM3.7AP MPC55xx ecus. Delphi DCM3.7AP Jtag MPC55xx pinout to Foxflash Delphi DCM3.7AP MPC55xx Solder the rainbow flat cable on the pcb: To read and write use the following driver: ->BDM/Jtag ->BDM/Jtag Mode ->Jtag Nexus… Read More »
Will Foxflash Read Kubota EDC17CV45 ECU?
Problem: Will foxflash programmer read and write edc17cv45 or not? I don’t see anywhere in software have Kubota edc17cv45, where it’s ? Solution: foxflash software does not have Kubota edc17cv45 driver on the list. But there is a BOSCH EDC17 CV54 [1767 ]– Agco [Diesel] driver. If the processor CPU is the same… Read More »
Foxflash Update FCA GPEC2 GPEC3 GPEC4LM GPEC2A ECUs
Good news! Foxflash ecu programmer released new update- adding FCA group GPEC2 GPEC3 GPEC4LM GPEC2A ECUs. Continental GPEC2 GPEC3 GPEC4LM GPEC2A – foxFlash is now able to perform the Continental GPEC2 GPEC3 GPEC4LM GPEC2A foxFlash is now able to perform the following operations: Boot Read Boot Write On the following ECU reference:… Read More »
Foxflash Read and Write MEDC17.9 OTP via OBD on Bench
OBD on the bench reading the MEDC17.9 with foxflash programmer+ godiag gt100 breakout box. I want to try and write the modified files via OBD after an OBD read. The ECU data that had been corrupted is now all OK. Updated: I have had an interesting case with this ECU MEDC17.9 that had failed… Read More »
Foxflash Failed to Read Honda EDC17CP16 Solution
Problem: I had issues with FoxFlash software clicking midway through reading and kicking you off. It did it a few times on the last ECU I read but just thought it may be a connection issue & managed to read ok. It’s doing exactly the same thing again. I’ve tried 3 different Power Supplies. Also tried… Read More »
Foxflash Read Mazda Denso SH13 Faster than Kess V2
After getting multiple failures on the bench due to the very tiny CAN-H and CAN-L pins on the Mazda CX-5 Denso SH13 ECU, I opted for OBD (on the bench) using the Godiag GT100 breakout box and I’ve managed to read the full flash with foxflash programmer, though it is much slower than on the… Read More »
Will Foxflash Read and Write Delphi DCM6.2 via OBD?
Will foxflash programmer read and write VAG Delphi DCM6.2 ECU via OBD? my kt200 doesn’t work. Yes, fox flash read and write DCM6.2 via OBD without issue. This ECU needs high voltage. At least 13.5v on car System! Only in car with immo! For example: VW Transporter T6 2.0tdi Delphi dcm6.2 read, ID, VR read,… Read More »
Foxflash Write SID310 Error SilentKey Solution
Problem: Foxflash reads Renault SID310 ok but Impossible to write sid 310 via OBD (Error SK2, Error Silentkey). Any solution? Solution: Start the engine and let it idle for 10 minutes, then it will allow you to write. If you turned it on, try to leave it for 10 minutes ONLY with the ignition on.… Read More »