Is it safe read write flash file from this Denso ecu (4N13) using pcmtuner via OBD? Car- 2012 Citroen C4 aircross, 1.8 d, 110 kw. I have tried to read with module 26 (identify and read ok, but afraid to write). Yes, go for it. pcmtuner read and write Denso 4N13 via OBD. It will… Read More »
Question: How to read (without opening) a Bosch ECU (0261S11653 / 8639595-01 / 170500554 DME) of a BMW 320i (F30) vehicle with foxflash? I have tried the connection in several ways… but so far without success. Solution: It is a MEVD17.2.9 ECU. Foxflash pinout to MEVD17.2.9 RED: + 12V 1, 22, 40 BLACK: GROUND 2… Read More »
How to read and write by FoxFlash through Bench mode Honda Civic MK10 2018 MED17.9.3 ??? Honda edc17 med17 have been done bench and boot. There are 2 options in FoxFlash, bench read and write through and another option bench and boot through pinout. Foxflash Honda MED17.9.3 bench pinout BOSCH MED17.9.3… Read More »
Problem: When i tried my first laptop to ID Honda Accord ECU as soon it did ID. After they i get USB not recognized error. Then i installed pcmtuner flash software in another laptop. Got every thing activated. Did ID honda eca via OBD. It did identified but again same error computer say USB not… Read More »
Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with… Read More »
Question: I was able to read Mini Cooper MEVD 17.2.7 EEprom and Flash from original and donor DME, cannot use the cloning function of foxflash, DME not listed. is possible to write flash, dme has OTP area. I tried on another dme some weeks ago and always canceled at 2%. What steps do i need… Read More »
Foxflash recent update adds FCA Dodge CONTINENTAL GPEC3 ECU. Here is the foxflash pinout to CONTINENTAL GPEC3 BAM SPC5674 CONTINENTAL GPEC3 FCA Pinout Connect with the multifunction cable the CNF1 on the pcb. READ AND WRITE ECU Use the driver: → TOOLS BOOT MODE → MOTOROLA FREESCALE BAM → CONTINENTAL GPEC3
Which tool to read this computer BMW MSV70 DME? Foxflash: Yes, via BDM Jtag Connect multifunction cable as follows: Solder the dip/sip connectors on the pcb and do a link: Insert Siemens/Marelli adapter as in photo: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x Ktag/Kess… Read More »
How to read this ECU Continental CM2150 E on Nissan/DAF using foxflash ecu tool? You can read CONTINENTAL CM2150E with fox flash by Jtag. Connect the multifunction cable as follows: First, you need to do a bridge in the following way: Solder the rainbow flat cable on the pcb: you need to do your… Read More »
Problem: Hello, I have a problem when writing simos18.1 with foxflash, the ecu is connected in boot. (I am sure it’s connected correctly because I checked it over 20 times and was able to read password and then files and do the write all successfully). When I try to write back by doing write all… Read More »
