CGDI FC200 ECU and TCU programmer released to V1.2.7.0 on April 29th, 2025. FC200 V1.2.7.0 New content: 1. Added the function of modifying VIN for some ECUs: (Bosch) BOSCH TC2xx: MD1CP001, MG1CS003, MD1CP002, MD1CS006, MG1CP002, MG1CS080, MD1CP004 SPC5777, MD1CP004_ TC298TP, MD1CS004, MG1CS001, MG1CS002 SPC5777, MG1CS002_ TC298TP, MG1CS111, MD1CP014, MG1CS008_ TC298TP, MG1CS016, MG1CS017, MG1CS018, MG1CS019,… Read More »
CG FC200 supports VAG DQ200, VL381, DQ250, DL381 gearbox mileage correction on bench. Here we will show how to correct mileage for DQ200 (0AM) gearbox. Select VAG Temic DQ200Dxx TC1766 gearbox in software. Check wiring diagram and connect gearbox with FC200. Connect CAN-L, CAN-H, 2x12V and GND cables. Identify gearbox. The mileage data is stored… Read More »
When working with the CG FC200 software to solve the ‘Three Readiness Monitors Not Ready’ issue with the Bosch ME7.8.8 ST10F275 ECU in Great Wall vehicles, it’s essential to follow the correct procedures to ensure successful communication and data handling. Below is a detailed guide on how to proceed, including the reasoning behind certain steps.… Read More »
Successfully cloned Chevrolet Sonic ACDelco E83 ECM using CG FC200 programmer on bench. Procedure: Select Acdelco E83 MPC5565 ECU. Check wiring diagram. Connect FC200 with original ECM. Connect and read VIN. Read and save EXT Flash data. Disconnect original ECM. Connect FC200 with donor ECM following the same wiring. Write flash to the donor ECM.… Read More »
Read Great Wall Bosch EDC16C39 ECU eeprom and flash successfully using CG FC200 programmer. Select Great Wall- Bosch EDC16C39 MPC561/2 ECU. Check wiring diagram. There are several versions of diagram. Fine one that matches your ECU. Connect ECU with MPCxxx adapter and FC200. Connect ECU. Read eeprom and save. Read flash and save. www.iecutool.eu
In the latest update, the CG FC200 ECU programmer added the “Three Readiness Monitors not Ready” function for GM Delco ECUs. FC200 released the new software version V1.2.5.1 on Jan. 15th, 2025. V1.2.5.1 Registered Version NEW (2025.01.15) New Functions: 1. Added Wuling SIM2K-51.4 read/write, VIN modification, and Three Readiness Monitors not Ready functions 2. Added Jinbei… Read More »
CG FC200 will do VAG MED17.5 ECU IMMO OFF in device directly without 3rd party software. Check instructions below: Run FC200 software, select Bosch MED17.5 TC1766 ECU. View wiring diagram Connect MED17.5 ECU with FC200 following the diagram Identify ECU. Read and save Dflash. Then read and save Pflash. Go to ECU selection, select… Read More »
Question: I need help to clear crash from this unit from a Toyota Highlander. 89170-0E400 Denso RH850 R7F701A223 I need pinout for read cpu. What software supports this module? CG100/CG100X will read this airbag module. iProg pro original also reset airbag crash for this module. OBDSTAR P50/X300 Classic G3 will also reset crash for this… Read More »
CGDI CG100X programmer released new software version V1.6.6.o on December 16th, 2024. CG100X new version V1.6.6.0 update details: 1. Added 35 airbag models. The following models are added for airbag. BAIC A00108504 R7F701A033(encrypted) BYD AUTO SA6H-3658100 R7F710643(encrypted) BYD AUTO SA3HV-3658100A R7F7010643(encrypted) DongFeng SX6H-5824010 R7F710643(encrypted) DongFeng SX7H-5824010 R7F710643(encrypted) DongFeng 988202GY0A R7F710643(encrypted) DongFeng SX5-5824010B R7F701A033(encrypted) Trumpchi… Read More »
How can you clone an ME17.3.0 ECU computer from the Fiat brand using CG FC200 programmer? These computers come on the Fiat FCA platform of the Mopard line. Run FC200 software, select Fiat, model and Bosch E17.3.0 ECU. Check the wiring diagram. FC200 gives 3 versions of pinouts. Try them one by one.… Read More »
