Mercedes Benz Bosch MED17.7.3.1 TC1797 ECU. CG FC200 read password ok, bench mode. Flex failed to read password. also bench mode. Flex is ok for this ECU. If it fails to read on bench, change power supply, use a 12v direct to a DC car battery. Flex also does VR obd, but if it is… Read More »
It’s a Peugeot 208 diesel model. Read and write with CG FC200 on bench mode. Read/write good. Adblue off. Automatic Checksum Correction. You need to do tprot off, them try to write the modified file. How about tprot? FC200 does tprot off automatically!
User report: Trying to read Peugeot Bosch MD1CS003 ECU with CG FC200 programmer but always get this error (Connection timeout. Check if the connection is correct.). All connections are fine. Autotuner read it fine. Check part number. If PSA MD1 ECU part number version is 034/035/036, it can be read on bench. If part number… Read More »
CG FC200 vs. OBDSTAR DC706: Which One is Better? The OBDSTAR DC706 is a versatile device designed for reading and writing engine control units (ECUs), body control modules (BCMs), and transmission control modules (TCMs). Here’s what makes it stand out: Key Features: Wide Vehicle Coverage: Supports a broad range of brands, including Chrysler, Dodge, Fiat,… Read More »
CGDI FC200 ECU and TCU programmer released to V1.2.7.0 on April 29th, 2025. FC200 V1.2.7.0 New content: 1. Added the function of modifying VIN for some ECUs: (Bosch) BOSCH TC2xx: MD1CP001, MG1CS003, MD1CP002, MD1CS006, MG1CP002, MG1CS080, MD1CP004 SPC5777, MD1CP004_ TC298TP, MD1CS004, MG1CS001, MG1CS002 SPC5777, MG1CS002_ TC298TP, MG1CS111, MD1CP014, MG1CS008_ TC298TP, MG1CS016, MG1CS017, MG1CS018, MG1CS019,… Read More »
CG FC200 supports VAG DQ200, VL381, DQ250, DL381 gearbox mileage correction on bench. Here we will show how to correct mileage for DQ200 (0AM) gearbox. Select VAG Temic DQ200Dxx TC1766 gearbox in software. Check wiring diagram and connect gearbox with FC200. Connect CAN-L, CAN-H, 2x12V and GND cables. Identify gearbox. The mileage data is stored… Read More »
When working with the CG FC200 software to solve the ‘Three Readiness Monitors Not Ready’ issue with the Bosch ME7.8.8 ST10F275 ECU in Great Wall vehicles, it’s essential to follow the correct procedures to ensure successful communication and data handling. Below is a detailed guide on how to proceed, including the reasoning behind certain steps.… Read More »
Successfully cloned Chevrolet Sonic ACDelco E83 ECM using CG FC200 programmer on bench. Procedure: Select Acdelco E83 MPC5565 ECU. Check wiring diagram. Connect FC200 with original ECM. Connect and read VIN. Read and save EXT Flash data. Disconnect original ECM. Connect FC200 with donor ECM following the same wiring. Write flash to the donor ECM.… Read More »
Read Great Wall Bosch EDC16C39 ECU eeprom and flash successfully using CG FC200 programmer. Select Great Wall- Bosch EDC16C39 MPC561/2 ECU. Check wiring diagram. There are several versions of diagram. Fine one that matches your ECU. Connect ECU with MPCxxx adapter and FC200. Connect ECU. Read eeprom and save. Read flash and save. www.iecutool.eu
CG FC200 will do VAG MED17.5 ECU IMMO OFF in device directly without 3rd party software. Check instructions below: Run FC200 software, select Bosch MED17.5 TC1766 ECU. View wiring diagram Connect MED17.5 ECU with FC200 following the diagram Identify ECU. Read and save Dflash. Then read and save Pflash. Go to ECU selection, select… Read More »
