Foxflash user feedback: Peugeot boxer 2,2hdi 2016 PSA SID208 is done with foxflash. Procedure to follow with foxflash. -Read password in obd (follow instruction foxflash) -Disassemble the vehicle’s ecu -Open up the ecu -Follow the pinout instructions provided by foxflash -Id ecu -Read the ecu -Modify file -Write the echo It’s 100% working. Foxflash SID208… Read More »
Here is the foxflash tool user feedback on 76F00XX BDM full read and write with 14V better supply. * Denso NEC76F0038AGD 175822-762 Toyota * Denso NEC76F0038AGD 175822-773X Toyota * Denso NEC76F0038AGD 175822-887 Toyota * Denso NEC76F0038AGD 211941-37900830 Toyota * Denso NEC76F0038AGD 211941-37910830 Toyota * Denso NEC76F0038AGD 275036-1152 Toyota * Denso NEC76F0038AGD 275036-2110 Toyota *… Read More »
Here comes the unbiased review of foxflash ecu programmer on June 1st, 2023. Credit to sazimam. “Because the FoxFlash is working very good for me. I decided to make this review of facts and tested procedures. It works only in ONLINE mode. You won’t run the software without it. It works only with the… Read More »
After getting multiple failures on the bench due to the very tiny CAN-H and CAN-L pins on the Mazda CX-5 Denso SH13 ECU, I opted for OBD (on the bench) using the Godiag GT100 breakout box and I’ve managed to read the full flash with foxflash programmer, though it is much slower than on the… Read More »
2012 Land rover Discovery 4 (EDC17CP11) successfully read, DPF and EGR delete, checksum by FoxFlash. All OK. Here’s the bench pinout to Land rover EDC17CP11 To read and write use the following driver: → BENCH TRICORE → LAND ROVER → TC1796 – Land Rover → EDC17 CP11 Read OK. Write OK. Car starts fine.
Most ask if foxflash ecu programmer will read and write PSA DCM7.1B ECU? Yes, foxflash does it without problem, the checksum is made by the tool. How to read and write DCM7.1b with fox flash? NEW BOOT MODE FOR DELPHI ECU DCM7.1A / DCM7.1B BOOT MODE for micro AURIX TC297 mounted on DCM7.1A and… Read More »
Foxflash ecu master tool read and write EDC16C3 PSA 1.4 HDI by OBD, Checksum ok by the tool, the vehicle starts ok. OBD just read flash data. Reading 6 minutes, writing 1.22 minutes. Image attached: If need to read/write both eeprom and flash, you need to read it on bench. BOSCH EDC16 C3 [ MPC556… Read More »
New test report: FoxFlash programming (read/write) John Deere 6430 premium engine control L14 via OBD port successfully. Connect foxflash with laptop and John deere via OBD In Foxflash software, select John Deere-> 6230-6330-6430 Premium->4.5L ENG CNTR L14′ CAN Foxflash read data very fast. Needs around 14v though. Then save data. Vehicle starts fine.
Here is the demonstration of unlocking a VAG Simos PCR2.1 ECU with Foxflash programmer in bench mode, unlocking allows all future programming to be done through OBD as well. FoxFlash PCR2.1 Unlock in bench mode PCR2.1 Unlock bench mode pinout To read and write use the following driver: → BENCH MODE → VW / AUDI… Read More »
VAG Audi Siemens PPD1.2G feedback! Foxflash online reading and writing Audi A3 170 hp PPD1.2G via OBD successfully. PPD works without Problems over OBD. These are supported VAG PPD.x list of fox flash. Audi car A3 2.0l 16V TDI Siemens PPD1 Audi car A4 2.0l 16V TDI Siemens PPD1 Seat car Altea 2.0l… Read More »
