Problem: Will foxflash programmer read and write edc17cv45 or not? I don’t see anywhere in software have Kubota edc17cv45, where it’s ? Solution: foxflash software does not have Kubota edc17cv45 driver on the list. But there is a BOSCH EDC17 CV54 [1767 ]– Agco [Diesel] driver. If the processor CPU is the same… Read More »
OBD on the bench reading the MEDC17.9 with foxflash programmer+ godiag gt100 breakout box. I want to try and write the modified files via OBD after an OBD read. The ECU data that had been corrupted is now all OK. Updated: I have had an interesting case with this ECU MEDC17.9 that had failed… Read More »
After getting multiple failures on the bench due to the very tiny CAN-H and CAN-L pins on the Mazda CX-5 Denso SH13 ECU, I opted for OBD (on the bench) using the Godiag GT100 breakout box and I’ve managed to read the full flash with foxflash programmer, though it is much slower than on the… Read More »
Will foxflash programmer read and write VAG Delphi DCM6.2 ECU via OBD? my kt200 doesn’t work. Yes, fox flash read and write DCM6.2 via OBD without issue. This ECU needs high voltage. At least 13.5v on car System! Only in car with immo! For example: VW Transporter T6 2.0tdi Delphi dcm6.2 read, ID, VR read,… Read More »
Problem: Foxflash reads Renault SID310 ok but Impossible to write sid 310 via OBD (Error SK2, Error Silentkey). Any solution? Solution: Start the engine and let it idle for 10 minutes, then it will allow you to write. If you turned it on, try to leave it for 10 minutes ONLY with the ignition on.… Read More »
Mercedes Benz SPRINTER 2019 CRD3P.B0 ECU read and write successfully using foxflash ecu programmer on bench. Checksum is done by foxflash. Foxflash pinout to Mercedes CRD3P.B0 To read and write use the following driver: → BENCH MODE → MERCEDES BENZ → TC1793 – MERCEDES and choose between: → CRD3P.B0 Read OK Write OK
Possible to read and write Ford Continental EMS2511 ECU with foxflash? by OBD or Bench? Yes, fox flash ecu programmer will read EMS2511 via OBD, bench and boot mode. OBD Mode: OK Ford Focus 1.5T 180ch ECU: Continental EMS2511 Conversion Flexfuel OBD Reading OBD Writing Checksum Fox Flash. Start up ok Bench… Read More »
Possible to read and write Opel ACDELCO E87 ECU with foxflash ecu programmer? Yes, OBD and bench work fine. OBD OK: Opel Atra j ACDELCO E87 Dpf egr off ,Read and write ok via obd. Bench Mode: OK Opel full system delco e87 Read/write ok Checksum by foxflash ok, voltage 13.5v car starts.… Read More »
VW POLO 2013 ECU PCR 2.1 unlock with foxflash ecu programmer in 3 minutes. Read and write ok, checksum manually with winols. I know foxflash will obd unlock and read file in 10s. I love bench because I can read ALL, in case something goes wrong I have a complete copy. I want a… Read More »
Foxflash ecu programmer successfully read and write 2016 Range Rover Evoque 2.0 ED4 MEDC 17.9 ECU. It is fine on bench, but cannot do Flexray ECU’s 2017 onwards. Connect the multifunction cable as follows: BOSCH MEDC17.9 [ 1793 ] – Land Rover [Diesel] pinout To read and write use the following driver: → BENCH… Read More »
