Question: Trying to read fiat doblo 1.6 diesel with foxflash but failed via obd and there’s no Pinout for this model. Anyone know if it’s possible to read / write with foxflash ? Solution: You can read your ecu on bench mode. there are 4 possibilities, tried them in order. Foxflash Fiat… Read More »
Foxflash programmer read and write Citroën DS3 2011 1.4 VTI ECU successfully. Bosch MEV17.4 ECU Read ok on bench Write ok on bench Stage 1 Checksum by foxflash Foxflash pinout to BOSCH MEV17.4 [ 1766/96 ] – Peugeot, Citroen [Gasoline] To read and write use the following driver: → BENCH TRICORE → PEUGEOT / CITROEN… Read More »
Problem: Why doesn’t foxflash let me read files? Toyota aygo Bosch ME7.9.5 ECU via OBD mode. the “read file” button is not lit. Solution: Foxflash does not have VR option for this ECU. Can only write map over OBD. Need to read on bench or boot mode. Foxflash pinout ME7.9.5 Bench mode … Read More »
Problem: Foxflash not connecting with Audi a4 2017 EDC17CP74 ECU. Any advise? Solution: Try another pinout V2. Use pinout from Pinout from ktag or dimsport. V2 pin out is not in foxflash. Feedback: All working now this was Audi A4 a 2017 edc17cp74. V2 pinout is slightly different with can high and low. Worked it… Read More »
Foxflash user feedback: Audi SQ7 2020 ECU MD1CP014 Mod+oil pressure+scr off Read ok bench Write ok bench Checksum by fox flash Foxflash pinout to Audi/Porsche MD1CP014 bench pinout To read and write use the following driver: → BENCH MODE → AUDI → TC298TP – VAG → MD1CP014 www.iecutool.com
Foxflash user feedback: Alfa Romeo 147 1.6i ECU ME7.3.1 Read flash/eeprom in full system bench mode Write flash OK, checksum not supported, done by winols. Ecu need 5 power pins, must have other pin to plug on 5 BOSCH ME7.3.1 – Fiat, Alfa Romeo, Lancia [Gasoline] Use driver full mode to communicate www.iecutool.com
Foxflash user feedback: Mitsubishi L200 2021 4N14 Stage 2 Plus Remapping Denso Ecu Reading ok Writing ok Checksum Correction by FoxFlash. Foxflash bench pinout to Mitsubishi 4N14 ECU DENSO 4N1x / 4D56 – Mitsubishi [Diesel] www.iecutool.com
Foxflash user feedback: Read and write Fiat Magneti Marelli IAW 5SF3.M1 ECU with foxflash successfully. Using full system pinout Read ok Write ok Checksum by tool Foxflash pinout to Marelli IAW 5SF3.M1 ECU
Foxflash new test report: Simos 8.10 boot read and write all fine with foxflash tool. Do not get a heart attack while flashing the ecu takes Power down and up. SIEMENS SIMOS 8.10 [ TC1796 INT.F.] – Audi Read and write ECU Connect with the multifunction cable the following pinout and the boot shown below. Use… Read More »
User feedback: Foxflash read and write BMW E90 ZF 8HP70 transmission gearbox successfully. Foxflas pinout to BMW ZF 8HP transmission Attention: There are 3 versions of pinouts, you can try all 3 without doing any damage. In addition to the ECU flash file, Foxflash software also saves the coding file.For writing:If you select the… Read More »
